When moisture finds its way into your compressed air lines, it can corrode pneumatic tools, contaminate finishes, and make your whole air system harder to trust. That's why refrigerated dryers are a common part of the air treatment setup for compressors and blowers. Two new refrigerant-type dryers are close in listed price: the Banfluxion 35 cfm Refrigerated Drying Equipment Compressed Air Dryer at USD 627.75 and the Central Pneumatic Industrial Refrigerated Compressed Air Dryer 21.6 CFM 3-In-1 Air Line Dryer at USD 685.70. Both are designed to remove moisture before it reaches your tools, but they differ in electrical service, flow scale, and how they process the air.
Quick verdict
If your compressor line needs a compact refrigerated package with a 600W R134A refrigerant circuit, the Banfluxion unit is the pick. If your line needs a 3-in-1 dryer that combines pre-refrigeration, evaporation, and air-moisture separation, the Central Pneumatic Industrial unit is the one to choose.
Side-by-side comparison
| Product | Listed price | Flow | Voltage | Dew point | Price bar |
|---|---|---|---|---|---|
| Banfluxion 35 cfm Refrigerated Drying Equipment Compressed Air Dryer | USD 627.75 | 35 cfm / 1.0 m³/min | 220V | 2-10 °C | |
| Central Pneumatic Industrial 21.6 CFM 3-In-1 Air Line Dryer | USD 685.70 | 21.6 CFM | 120V | 36°F |
Where each dryer fits best
The Banfluxion is built for continuous line drying: the specs include an inlet temperature ceiling of 45°C, working pressure up to 1.0 Mpa, and a compact footprint that matches the compressor's displacement. It's the stronger match when you want that package in a single refrigerated unit.
The Central Pneumatic Industrial is built around a 3-in-1 treatment process with pre-refrigeration, evaporation, and air-moisture separation, plus a 1/2-inch inlet and a 140 PSI pressure rating. It's the stronger match when you want that integrated process in one air-line dryer.
Product notes
Banfluxion Refrigerated Drying Equipment
Pick the Banfluxion when you want a compact refrigerated dryer with a 600W R134A refrigerant circuit and a control setup designed for a 220V feed. Its operating envelope includes an inlet temperature ceiling of 45°C and working pressure up to 1.0 Mpa, which points to continuous line drying in that range. The lower listed price of the two is also in its favor, especially if the voltage side of your shop already matches. The trade-off is electrical service: at 220V it won't run off a standard 120V shop outlet, so your electrical setup has to match that input before this unit becomes the right fit. If your lines are already wired for 220V, this compact package is the one to measure first.
Central Pneumatic Industrial 3-In-1 Air Line Dryer
Choose the Central Pneumatic Industrial when you want the 3-in-1 approach-pre-refrigeration, evaporation, and air-moisture separation-in a single unit. The spec set includes a 1/2-inch inlet, a 140 PSI pressure rating, and a description that says it removes up to 90% of moisture from the line while lowering the dew point to 36°F. That kind of integrated treatment is convenient because you don't assemble separate stages yourself. The limitation is scale: its flow ceiling sits below the other unit's higher flow rating, and it lists above the other price, so it suits smaller air lines rather than big-volume compressor systems. If your compressor output is on that moderate scale and you want one box to do the moisture job, this is the unit.
Final choice by use case
Pick the Banfluxion 35 cfm Refrigerated Drying Equipment Compressed Air Dryer when you want the lower listed price and a compact refrigerated design for a higher-flow line. Pick the Central Pneumatic Industrial 3-In-1 Air Line Dryer when you want a single unit that handles pre-refrigeration, evaporation, and moisture separation for a moderate-flow line.
